Kirjeldus

M-Tac has released a MODULAR MULTICAM DRONE BACKPACK, which will be a great addition to your kit. The backpack consists of two main compartments. The first is equipped with a special organizer for convenient storage of drones, their charging units, batteries and remote controls. The inner panels of the compartment are made of velcro fabric allowing you to adjust the organising dividers according to your needs. The upper and lower bays of the organizer are designed for carrying remote controls, the middle ones are for drones and their chargers, and the smaller cells are for batteries. On each of the larger bays an elasticated strap provides additional security for the contents. On the flap of the first compartment there is a pocket for a tablet, which closes with a Velcro strap. Above it there is a pocket with a zipper, intended for placing your essentials. On top of the flap there is a cardholder for storing 5 memory cards and a special pocket for placing drone propellers. In the second main compartment there is also a card holder for storing 5 memory cards and an organizer designed for placing batteries, cords from chargers, etc. There are MOLLE systems on the front and sides of the backpack, to which you can attach additional equipment. Also, on the front of the backpack there is a pocket with a moisture-proof zipper, and a velcro panel with slots, designed to accommodate both additional equipment, as well as IDs and patches. On the top and the sides of the backpack there are special handles made of webbing to conveniently carry the backpack. Webbing straps attached to the bottom of the backpack are intended for attaching equipment. The backpack is made of Cordura 500 – a durable material that is resistant to abrasion and high loads. The side walls of the backpack are reinforced with soft polymer material EVA foam and innovative material Tegris (100% polypropylene), the main property of which is wear resistance, high strength and protection against damage. Materials: Cordura 500D; velcro canvas; Reinforcement of side walls: EVA foam, Tegris; Hardware: Woojin; Zippers: YKK (Japan); Webbing: Murdock; Dimensions: 42 * 25 * 12 cm. Due to its unique qualities Cordura is widely used in tactical equipment of military, law enforcement and special forces. It is mainly materials with linear density of 1000d and 500d. Linear density – is the ratio of weight of the thread of matter and its length. It is measured in denier. This unit of measurement is mainly used for nylon products. Accordingly, the higher this value, the thicker and heavier the fabric. The physical and technical characteristics of CORDURA 1000D fabric are very high, breaking load is about 3000 N, breaking load is about 150 N. The abrasion resistance is over 50,000 cycles. It is used for clothes, covers, pouches. Be it a tactical backpack, pouches or jacket.Products made of CORDURA materials will undoubtedly pass the test of time and distance. CORDURA is durability, reliability and style. In terms of strength, it is beyond any competition. Woojin plastic® – is a world renowned company for the production of quality plastic fittings. Woojin plastic® – is a Korean company founded in 1979. The company’s headquarters were in Korea until 1993, after which it moved to the United States. Since then, the company has grown even faster. Thus, in two years, the company’s exports grew to 1 million dollars and continued to grow. In 2002, the company obtained international ISO 9001 certification. Today Woojin is one of the world’s best manufacturers of plastic fittings for the military, climbers and alpinists. Very important components in the creation of Woojin plastic is ACETAL. It gives the material such qualities as: hydrophobicity, wear resistance, strength, rigidity and form stability. Distinctive feature in comparison with other materials is also its dimensional stability, so all components made of ACETAL are identical. ACETAL is also not replaceable in humid environments; its quality is not a bit worse compared to polyamide. YKK company is the world leader in production of zippers. It manufactures 90% of all such zippers in 71 factories around the world. This is a group of Japanese companies whose trademark was registered almost 70 years ago. YKK is deciphered and translated from Japanese as “Yoshida Factory” – the name of the company’s founder, who opened the production of clothing clasps in the 1930s. Success was achieved through cooperation with leading clothing brands and the introduction of particularly strict quality standards. In addition, for a very long time the machine for the production of quality clasps kept a strict secret. This helped the company to quickly circumvent its main competitors.